Roborock Qrevo Pro Vacuum Review

The Roborock Qrevo Pro feels impressively well-built. It's very similar to the standard Roborock Qrevo in this respect, with a sturdy, dense-feeling construction. Its top cover has a glossy finish, which tends to attract quite a few fingerprints, while its bumper and lower half have a matte finish. Like its cheaper stablemate, the mop pads are held in place with magnetic pegs, but in the Pro model's case, the right-most mop mount moves outward in a slight arc so that it can clean deeper into corners. This mechanism feels quite robust, with minimal play or jiggle within the system. There are a few downsides, however: finer debris can get into the hinges for its dustbin cover, to the point where it doesn't close fully, as seen here. This has no impact on the operation of the vacuum, but it does look pretty unseemly, especially for a higher-end model like this.

The multifunction dock also feels similarly sturdy to the vacuum. However, it's worth noting that it is very large since it not only has an integrated dirtbag for solid debris but two water tanks: one is for refilling the vacuum's internal water tank, while the other holds wastewater collected after the dock has rinsed the vacuum's mopping pads.

The Roborock Qrevo Pro has a reasonably high number of components that need to be cleaned periodically, but on the upside, they're pretty easy to access. Components that are often used, like the brushroll, dustbin, and vacuum filter, can be removed without the need for any tools, and cleaning them is simple. It doesn't take much hair to cause the brushroll to jam, but it also doesn't have any bristles for hair to get stuck. As for the filter, its dense pleats tend to collect a lot of debris, so it's best to rinse it to clean it properly. On the downside, you do need to unscrew the side brush with a Phillips-head screwdriver, and you'll need a flat-headed screwdriver to lever the omnidirectional wheel out of place.

The multi-function dock takes quite a bit of the sting out of everyday maintenance since it not only empties the vacuum's internal dustbin but also refills its internal water tank and washes its mopping pads with heated water and dries them. That said, this dock also incurs its own set of maintenance requirements. You'll need to dispose of its dirtbag, wash out the dirty water tank periodically, and refill its clean water tank. The dock also features a separate cleaning tank and water filter for the mop washing element at the base of the dock. Once again, however, these parts don't take much time to access.

If you'd like to read a breakdown of the maintenance procedures involved with this vacuum, you can read the maintenance guide here. Roborock also has a series of videos detailing maintenance procedures for the Roborock Qrevo MaxV on their YouTube channel, which requires similar overall requirements. You can view those videos here, here, and here.

This vacuum incurs high recurring costs.

• Brushroll: You'll need to replace the brushroll after 300 hours of use or every six to 12 months. Replacements can be purchased here.
• Side brush: The side brush has a service life of 200 hours or approximately three to six months of use. You can buy a two-pack of replacements from the company's website here.
• Filter: The filter needs replacing following 150 hours, according to the maintenance tab of the companion app, or every six to 12 months. You can buy replacements in packs of two here.
• Mop pads: You should replace the mop pads every one to three months. Replacements can be purchased here.
• Multi-function dock dirtbag: The dirtbag has an advertised capacity of 2.7L. Replacements can be purchased here.

Much like the standard Roborock Qrevo, the Roborock Qrevo Pro takes up a fair amount of space. While the vacuum itself isn't big, its multifunction dock certainly is since it has to fit an internal dirtbag, two water tanks for clean water and wastewater, and a dryer for its mop pad. There's a groove at the back of the dock for storing any excess length of power cable. It's worth noting that this multifunction dock is fractionally shorter than that of the standard QRevo, as its water tanks have a smaller capacity of 4.25L rather than 5L.

This vacuum's debris capacity is similar to that of the older Roborock Qrevo. Its dock uses dirtbags with the same 2.7L capacity, enough for a few weeks' worth of debris. At 0.25L in capacity, its internal dustbin is slightly larger than that aforementioned model but is still on the smaller side.

Since the vacuum's internal water reservoir is built into it and you can't remove it, we can't verify its capacity. The twin water tanks in the multifunction dock each have a max capacity of 4.25 L.

• Roborock Qrevo Pro vacuum
• Dirt compartment
• Multifunctional Dock
• Multifunctional Dock base
• Multifunctional Dock Cleaning tank
• Multifunctional Dock Cleaning tank filter
• Clean Water Tank
• Dirty Water Tank
• Multifunction dock power cable
• 2x Disposable dirtbags
• Dirtbag compartment cover
• Cleaning tank
• 1x Washable filter
• 1x Rubber brushroll
• Brushroll guard
• 2x Mopping pads
• 2x Mopping pad mounting plates
• Quick Start guide and User Manuals

The range is limited only by the remaining battery life, but like any robot vacuum, it can't climb or descend stairs.

This unit is somewhat heavy for a robot vacuum, but it's still ultimately lighter than some flagship models. There's no carrying handle to make it easier to bring up and down stairs.

This vacuum's battery performance is superb. It uses the same 5200 mAh lithium-ion as the Roborock Qrevo and, unsurprisingly, has a similar runtime. In its low-power 'Quiet' mode, it can run for a little over four hours, which gives it plenty of time to deal with lightweight debris. Its battery life drops to just under two hours in its high-power 'Max+' mode. This is still enough time to deal with stubborn messes on surfaces like carpet. This vacuum also features an 'Off-Peak Charging' function, which allows the vacuum to recharge only during peak hours for power demand to save on electricity costs. You can keep track of the vacuum's battery status by checking the indicator light at the top of the vacuum, which changes color and pattern depending on the current charge status.

The Roborock Qrevo Pro is a feature-packed robot vacuum. Like the older Roborock Qrevo, it has an Auto-Mop Lift feature to raise the mop pads on carpeted surfaces so that it can run vacuuming and mopping jobs within the same cleaning cycle. However, the system has been upgraded for this unit, and it now raises the mopping pads by 10mm instead of 7mm. The upgrades to its mopping system also include its swing-out arm, which can get the mopping cloth further into corners and along walls.

There are also a variety of carpet-specific cleaning functions: 'Carpet First' mode has the vacuum clean carpets before anything else in its cleaning cycle to prevent them from getting wet, while the 'Deep Carpet Cleaning' mode has the vacuum run on carpets twice at a higher suction power level setting. You can also have it avoid carpets entirely. You can manually choose between its five different power level settings and two different vacuuming route modes.

Its SmartPlan AI system is a pretty unique selling point; the manufacturer advertises it to allow the vacuum to automatically select the optimal vacuuming and mopping modes for different rooms. For instance, if in a bedroom, it would automatically change to the 'Quiet' power setting and 'Gentle' mop setting, whereas it would increase its suction and mopping intensity in a tile-floored kitchen.

There are a variety of mopping options, too. You can choose between three water flow levels for its mopping pads: 'Low,' 'Medium,' 'High,' and 'Custom.' There are also four levels of route mapping settings, which effectively allow you to choose between fast and deep mopping on a sliding scale.

The Qrevo Pro also features Roborock's Reactive Tech system, the company's entry-level hazard avoidance technology. It features a front-facing structured light sensor to spot hazards, but this type of sensor ultimately isn't as sophisticated or as effective as the RGB-color camera-based system found on the Roborock S7 MaxV.

This vacuum has a three-armed side brush to direct debris into the path of its rubber roller. It also comes with a pair of washable mop cloths that are velcroed onto magnetically mounted rotating base plates.

The Roborock Qrevo Pro's performance on hard floors is mediocre. It tends to leave behind a noticeable amount of medium-sized and fine debris like rice or cereal, especially along corners and walls. Its performance lags behind the supposedly older and less powerful Roborock Qrevo, as its roller brush tends to jam easily when it runs over bulkier debris like cereal. Increasing the suction power to 'Max+' shrinks the gulf in debris pickup performance, as seen here, but the downside of this setting is that its battery is drained considerably faster.

The Roborock Qrevo Pro delivers decent performance on high-pile carpet. It's very good at dealing with medium-sized debris like rice. It's reasonably effective in clearing away larger material like cereal on this surface type, though you might want to have it run another cleaning session to clear away finer debris like sand that's been worked into this surface type, especially along walls and in corners.

Note: We initially encountered some difficulty testing this vacuum on our black sample carpet due to the vacuum's cliff sensors triggering, which would cause it to stop moving and miss entire sections of the floor, as seen here. This isn't necessarily something that will impact most people, but it's worth noting that this vacuum can have trouble maneuvering on especially dark-colored surfaces.

The Roborock Qrevo Pro's performance on low-pile carpets is okay. It's quite effective in dealing with large- and medium-sized debris like cereal or rice, but it'll need to make an extra pass to deal with finer debris that's been pressed deeper into carpet fibers, especially in corners and along walls.

The Roborock Qrevo Pro's pet hair pickup performance on low-pile carpeting is fair. It'll clear away lighter strands of hair lying on top of carpeting but will struggle with strands that have been embedded a little more deeply, so you might want to run several cleaning cycles if you have pets that shed heavily. On the upside, its rubber brushroll is quite easy to clean.

The Roborock Qrevo Pro's suction force isn't very strong, largely because its suction inlet is positioned too high above the contact surface to generate a tight seal on bare surfaces, resulting in low suction power measurements.

This vacuum's airflow performance is good overall for a robot vacuum, though hardly a step up from the older Roborock Qrevo, despite its claim of having a more powerful motor. This difference could be attributed to the Qrevo Pro's smaller filter opening when compared to the older model, which can have a negative overall impact on airflow.

This vacuum is incredibly quiet. You'll hear what people nearby say even when the vacuum runs in its most powerful suction mode within the same room.

The multifunction dock is noisier than the vacuum when using the self-empty function, with a peak volume of 69.5 dBA, though this does make it quieter than the Roborock Qrevo's dock.

The maneuverability is similar to that of the standard Roborock Qrevo, which is great. Its LIDAR sensor maps out rooms quickly, moves in an organized pattern in its 'Normal' pathing mode, and is small enough to clean under most tables and chairs without getting stuck. While the Reactive Tech hazard recognition system isn't the most sophisticated within Roborock's lineup, it can still spot and recognize hazards like thick shag-pile rugs that it would get stuck on, though it might not spot smaller, lower hazards like power cables.

The Roborock Qrevo Pro does a poor job of sealing in fine particles. Fine allergens can bypass its exhaust filter and are blown straight out of its exhaust port and LIDAR sensor.

Like many other robot vacuums, the Roborock Qrevo Pro struggles with debris in cracks and crevices. Its side brush tends to drag debris outwards instead of directing it toward the suction inlet. Running the vacuum in the 'Max+' suction mode makes little to no difference in terms of performance in this regard.

The Roborock Qrevo Pro's stain-clearing performance is good, with the water flow mode set to 'High' and the pathing set to 'Deep+.' Its rotating mop pads are exceptionally effective in scrubbing away dried-on stains, and the FlexiArm extending mop design allows for a much closer clean along walls and in corners compared to most conventional hybrid vacuum/mops.

The multifunction dock's mop-washing process is impressive. After the vacuum has finished mopping, it'll park at the multifunction dock, where the pads are cleaned with water heated to 128.4°F (53.3°C) before being dried with a flow of warm air. You can see how the pads looked before the automatic clean cycle here, and after the clean cycle here.

The dock also has a 'Dirt Detection' feature, which will send the unit back out for another mopping run, depending on how dirty the mop wash water is.

The Roborock Qrevo Pro isn't designed to deal with liquid spills. It can clear away small spills by soaking them away with its mopping pads, but having the vacuum suck up liquid is likely to damage it.

This vacuum has a broad array of physical automation features. Its multifunction dock eliminates a lot of the normal day-to-day maintenance requirements that come with a robot vacuum, as it empties the vacuum's dustbin, refills its water tank, washes its mop pads with heated water, and dries its mopping pads.

There are two physical control buttons that you can use to perform basic functions, without having to use the app. The power button doubles as a general 'Clean' button, sending the vacuum off to map your home and start a cleaning session. You can press the 'Home' button to send the vacuum back to its base station. Holding down the 'Home' button engages the spot cleaning function, in which the vacuum will clean a small area around itself.

The Roborock app has a remarkably dense feature set; you can see its interface here.

After it's mapped out your home, you can set up no-go zones, designate specific cleaning zones to spot clean, split, merge, and name those areas, manually set the surface type for different areas, and set the suction and mopping modes you want for individual rooms and even tweak the order through which it moves through each room. You can also set 'Entrapping Areas,' zones where the vacuum will slow down to minimize damage on delicate surfaces, like door thresholds and steps. It also offers multi-level mapping for up to four floors.

You can adjust its 'Less Collision' mode through two different modes, which causes the vacuum to avoid contact with walls and furniture at the expense of lower-precision scanning in tight spots.

The app also has a 'Help' sub-menu that gives you a projected service interval for its filter, brushroll, side brush, sensors, and mopping pad.

There are also quite a few configuration options for the multifunction dock. You can adjust the frequency of mop-washing cycles, the mop-washing intensity, and the mop-drying cycle length. You can also adjust how often the vacuum will return to its dock to self-empty depending on the size of your home or simply leave it up to the vacuum itself.